Radar Basics: An Overview of Electronic Warfare Part 2

October 30, 2018 Mario LaMarche


In the first post of this series, we discussed the history of electronic warfare with an emphasis on the back-and-forth competition to develop systems that grant the owner control over the electromagnetic spectrum. When one country develops a new radar system, its adversary starts working on a jammer. In order to mitigate the effects of the jammer, the radar developer then must design a system that protects the radar from those effects.

This invisible battle over control of the electromagnetic spectrum is critical to success on the battlefield and is the topic of the subsequent posts. However, understanding the technology to jam and deceive radar requires an understanding of the radar systems.

We’re all familiar with the applications of radar—that yellow warning light on your mirror telling you someone is in your blind spot, police radar monitoring your speed, images on the news showing the path of a storm. However, for the purpose of understanding electronic warfare, we’ll look at the types of radar in three main groups.


Three Types of Radar Systems

Search radars scan over long ranges and wide angles to locate targets. For example, early warning systems can detect distant threats to provide adequate time for a response. These types of radar systems often operate at lower frequencies since range is prioritized over resolution. Because range is so critical, these systems are sometimes installed on-board aircraft to increase the line-of-sight to the horizon.

Tracking radar systems accurately measure a small number of targets—often just one. By operating at a higher frequency, the resolution is increased, providing improved accuracy. Additionally, instead of scanning a large area, they focus on a much smaller region in order to continuously monitor their target. Fire-control radars employ this type of system.

Imaging radars employ a variety of techniques to analyze an area to create an image. For example, airborne synthetic aperture radar (SAR) can be used to create images of landscapes. The below image is of the Teide Volcano in the Canary Islands and was created using a space-based synthetic aperture radar on-board the Space Shuttle Endeavor.


Radar Basics

Now that we’ve broken down types of radar by their application, we’ll move on to describing the details behind their operation.

At its core, radar technology is simple. The transmitter sends a signal towards the target. Some energy from this pulse reflects off of the target and is received by the radar system. Since the radar signals propagate at the speed of light, measuring the elapsed time between sending the original signal and receiving the reflection allows for a calculation of the distance. By confining the radar signal to a narrow beam, the location of the source of the reflection is known.

Doppler Radar

The approach above provides the distance to the target and the angle of the target relative to the radar system. However, what if we also need to understand how the target is moving? To do this, we use Doppler radar.

If you aren’t familiar with the Doppler effect, it explains why the pitch of a siren appears to change right as the ambulance drives past. In terms of radar, the frequency of the reflected wave is modified as a function of the reflector’s velocity. In practice, the velocity of the target is determined by analyzing the phase shift in the received radar signal. Measuring this phase shift requires the transmitted radar pulses to have the same phase offset. While creating coherent pulses is a challenge, it enables a much more capable radar system.

In addition to determining the target’s velocity, Doppler radar can filter out reflections from objects with low velocities. In the case of an airborne Doppler radar, this technique is able to discard many of the reflections from the ground. Referred to as “ground clutter rejection”, this technique increases the radar’s ability to easily identify other airborne targets—especially those flying low near the source of the unwanted ground reflections.

Range and Resolution

Next, we’ll describe two key performance metrics of a radar system—range and resolution—and discuss some common techniques to improve them.


To understand how to optimize the range of a radar system, we first need to review some of the factors that determine the range. Depending on the gain of the antenna, a percentage of the transmitted power is incident on the target, and depending on the target’s radar cross section, some of that power is reflected back to the radar antenna. As the range is increased, less and less power returns to the radar receiver. When the received power of the signal is close to the noise floor, the range of the radar has been exceeded.

Obviously, increasing the transmitted power also increases the received power. One way to accomplish this is through the use of a GaN-based power amplifier. This high-power technology supports increased output power in a small form factor. A less obvious approach is to integrate multiple pulses. Since the noise is roughly random in nature, averaging multiple measurements improves the signal-to-noise ratio and therefore increases the radar’s range.


As described above, tracking radars need to accurately locate the target with high resolution. Operating at a high frequency is one way to improve the resolution of the radar. Another approach is shaping the waveform, using techniques such as pulse compression. Linear frequency modulation, commonly referred to as “chip”, is one type of pulse compression. While the details are beyond the scope of this article, they result in the radar receiving narrower pulses, which improve the resolution of the radar.

What’s Next…

While much more can be said regarding the functioning of radar systems, this brief introduction provides the necessary background for the subsequent posts. In the next article we present a brief overview of electronic support, followed by posts on the other two main elements of electronic warfare—electronic attack and electronic protection. In terms of radar, electronic support involves locating an adversary’s radar system, electronic attack involves degrading an adversary’s radar system, and electronic protection involves protecting a radar system from the effects of an adversary’s use of electronic attack.

Part 3: Electronic Support


Previous Article
The History of Electronic Warfare: An Overview of Electronic Warfare Part 1
The History of Electronic Warfare: An Overview of Electronic Warfare Part 1

It was May 24, 1844 when Samuel Morse transmitted his famous telegraph message “What hath God wrought” from...

Next Article
Electronic Support: An Overview of Electronic Warfare Part 3
Electronic Support: An Overview of Electronic Warfare Part 3

“They have a missile-lock on us!” is a phrase we’ve heard countless times in movies and is usually a sign t...


Let's Talk. Contact Sales

First Name
Last Name
Phone Number
Product Category
Product Title or Part Number
Comments or Inquiry
Thank you!
Error - something went wrong!